This page contains all the firmware release notes for the Ultimaker S5.
Skip to release notes for:
Camera stream in Digital Factory. Printers will now be able to stream pictures from the printers camera onto the Digital Factory. Pictures will be refreshed every 10 seconds
Ultimaker S5 Pro Bundle:
Material Station lights. The Material Station frame lights are dependent on the Ultimaker S5 frame lights, and will adjust along with the Ultimaker S5 frame light brightness. The Material Station LED lights above the eject button are not adjustable and will remain on
Fixed some cases where, aborting a print at the wrong moment, would result in a blocking ER56 / ER61 error.
Fixed an end of filament bug: Fixed a case whereby the printer did not continue printing at an end of filament, while there was available material.
Revised board powerdown routine. Improved voltage control due to improved powerdown routine.
Connect to Ultimaker Digital Factory. Adding printers to the cloud is now adding printers to Digital Factory. You can now find your online dashboard at digitalfactory.ultimaker.com
Advanced cloud features. Printers running this firmware will be able to make use of advanced cloud features, such as print queue management and reprint form history as well as features such as renaming and identifying printers from the Digital Factory printer management console
Simplified cloud connectivity. The cloud connectivity workflow has been simplified. From your printer, when connecting to digital factory a pin code will be displayed. This pin code will be enough to connect your printer. Connection can be established from outside of local network
Update printer via cloud. Users will be able initiate a firmware update from their printer management console on digitalfactory.ultimaker.com
QR codes displayed with error messages. Troubleshoot your issues faster by scanning the QR code that displays on screen when an error message appears
Introduced data sharing for Error codes. We have introduced a data sharing feature for network connected printers. This data sharing will facilitate our product improvement by helping us track what sort of errors our users are encountering. You can opt out of this in the settings menu
Ultimaker Pro Bundle
Faster prime and deprime. Purge priming and depriming for the Ultimaker S5 Pro Bundle has been made faster. When a print job is started that uses the same material as the previous print job, the purge process will use less material leading to a quicker start of print. The purge process at the end of a print will also consume much less material
Wizard for ER61 / failure to break from printhead. To reduce incidence of ER61’s, a wizard has been introduced to prevent the error from occurring. Follow the wizard to fix the blockage when filament is unloading
Purge speed dependant on nozzle size. The purge procedure will now adjust the volume purged according to the print core used
Air Manager filter tasks. User will now get a task informing them when it is time to replace the Air Manager filter
Fixed camera dropping out – Fixed an issue which caused the camera feed to stop working during operation
Fixed bug that could corrupt NFC tags. If a material NFC tag information gets corrupted during writing of information to the NFC tag, this is repaired afterwards.
Bug fix for printing via USB – When printing via USB the Pro Bundle will no longer ask for a configuration change if the correct material is loaded
Fixed translation typo in print time left. Several languages had a typo displayed during the print time remaining screen, showcasing the wrong units. This has been corrected
Filament handling improved during loading of filament. Filament handling has been improved, and the Pro Bundle will now correctly handle the end of filament if the filament is in the load to printhead state. Aborting during the load to printhead state also works correctly
Air Manager steps included in welcome setup. The Air Manager steps are now included in the
printer welcome setup
Guided Air Manager filter replacement. Users are now guided through the process of
changing / installing a filter for the Air Manager
Air Manager communication error. Fixed printer behaviour when encountering a communication
error, such as cable disconnect during printing
Air Manager fan speed re-calculated when transition in different states. The Air
Manager fan will now correctly re-calculate its speed when switching from a maintenance
action to a print job
Improved material unloading reliability. Improved handling of the filament during end of
filament should reduce prevalence of ER61’s
Quieter Air Manager fan. Material-specific look up tables control the Air Manager fan speed. New, improved look up tables result in a quieter Air Manager fan for most materials when printing at ambient temperatures (22 °C / 72 °F).
Cloud printer removal. Disconnecting a printer from the cloud in Ultimaker Connect now also removes the printer from your associated online cloud account.
Print job previews in cloud. Print jobs sent via cloud now show print job preview images in the cloud as well
About Air Manager screen. Removed a touch interface screen which looped onto itself.
Error message print core numbering. Standardized all error messages to refer to print cores 1 and 2.
Reduced prevalence of ER998. Firmware 5.4.24 introduced two new error codes, ER999 and ER998. A bug has been fixed which frequently triggered ER998.
Memory improvements. Enhanced memory management for the Ultimaker S5 enables additional functionality with Ultimaker peripherals.
Support for the Material Station. Enables the Ultimaker S5 to be used with the Ultimaker S5 Material Station peripheral.
Support for the Air Manager. Enables the Ultimaker S5 to be used with the Ultimaker S5 Air Manager peripheral. (Further optimizations to material-specific configurations coming soon.)
Firmware 5.2.11 is a hotfix release to correct issues reported in firmware 5.2.8. This hotfix will address the issues discussed below:
Update via USB. Fixed an issue where printers without a network connection couldn’t update to the .swu file system. Users that tried to upgrade to firmware 5.2.8 via USB would get stuck on the stepping stone version due to a mismatch between the onboard time stamp of the printer, which would default to standard Linux (UNIX) time, and the timestamp of the downloaded file.
XY calibration. Fixed an issue which prevented the XY calibration procedure from extruding properly. All printers running firmware 5.2.8 would initiate the XY calibration procedure with filament in a retracted state. This meant that the procedure would finish its sequence without extruding correctly. Firmware 5.2.11 ensures that filament is fully primed before initiating XY calibration.
Screen issues. Fixed an issue where the screen on the Ultimaker 3 shifted or rotated. Firmware 5.2.11 included a redundant feature that was interacting with the Linux kernel in an unexpected way, leading to shifted or rotating screens. This feature has been completely removed in firmware 5.2.11.
Third-party materials. Abrasive materials have been removed from the Ultimaker 3 material selection menu, as printing abrasive materials will damage the Ultimaker 3 feeder wheel.
Wi-Fi on the Ultimaker 3 and Ultimaker S5
We’ve received some reports on unstable Wi-Fi functionality on the Ultimaker 3 and Ultimaker S5, and we are currently researching a solution. If the Wi-Fi setup does not connect to your network, we recommend performing a factory reset and trying again. This will allow you to repeat the Wi-Fi setup so you can connect your printer to your network.
March 21, 2019
Remote printing. In combination with Ultimaker Cura 4.0 and an Ultimaker account, the new remote printing feature is enabled. Send print jobs to your Ultimaker 3 or Ultimaker S5 from anywhere in the world and stay informed of the print process no matter where you are.
Model-based active leveling. We've revisited the active leveling process for the Ultimaker S5 to make it more efficient. Instead of probing the entire build plate, the footprint of the model is probed before a print begins, and any disabled nozzles are skipped from the process, so that printing can begin much faster. Model-based active leveling works on the Ultimaker S5 only when sliced with the latest version of Ultimaker Cura, with 'print all at once' enabled.
Filament runout detection. We've optimized filament runout detection for better accuracy. Filament flow settings are now embedded in the UFP file so that it is material-specific.
Leveling sensor test. We've added a new item in the maintenance menu of the Ultimaker 3 and Ultimaker S5. The leveling sensor test checks if the capacitive sensor in the print head is working properly, to keep it in top condition and to let you know if maintenance is needed. The leveling sensor test reports if (a) the sensor is working correctly (b) signal interference is detected (c) the sensor needs maintenance.
Various bug fixes. For a better user experience, we've reduced the noise when lowering the build plate when prints are finished. The internal lights of the Ultimaker S5 can now be completely turned off. The bed temperature for TPU materials is optimized during XY calibration for better reliability.
2 January, 2019
Version 5.1.8 adds the following bug fixes:
Resolves a print initiation issue when using third-party materials
Makes it possible to view third-party materials offline
Fixes a Cura Connect issue that erased recent history when deleting a file from the queue
October 31, 2018
Faster active leveling. Active leveling is now approximately two minutes faster on the Ultimaker S5. This is achieved by reducing the time probing the Z-height at each point of the grid. Some improvements have been ported to the Ultimaker 3, while still maintaining a 3-probe sequence. More speed improvements are due in the next release.
Accuracy and reliability improvements. Small blobs under the nozzle or build plate caused inaccuracies during active leveling and print core heating. To minimize the chances of this, each sequence has been improved for better accuracy.
Flow sensor accuracy. Material run-out detection for the Ultimaker S5 is now more efficient, with reduced latency between run out detection and pausing. This means less missed extrusion, and a reduced chance of artifacts showing on a finished part where material has run out and been replaced mid-print.
On-screen release notes. Release notes with descriptions of new features are now visible on the Ultimaker S5 touch screen when a firmware update is available.
Print end bed temperature. The build plate temperature now remains visible on the Ultimaker 3 screen, even after it has cooled below 60°C, making object removal easier and more informed for users.
This release includes significant improvements for power users of Ultimaker Connect. A lot of these features are also reflected in the new Ultimaker app.
Ultimaker 3 and Ultimaker S5 grouping. Use Ultimaker 3 and Ultimaker S5 printers together in the same group.
Maintenance notifications. When a maintenance task is due, an icon is displayed on the specific printer in the Cura Connect interface.
Rendered preview. The Ultimaker Connect interface now shows a rendered preview of GCODE data for Ultimaker 3 print jobs for visual reference.
Firmware update notifications. The Ultimaker Connect interface highlights printers that can be updated with new firmware. This saves having to check and update each printer manually using the built-in display. Updates can be deployed to connected printers via the Ultimaker Connect interface.
Rename printer. Previously printer names had to be changed by running the Wi-Fi setup on each printer. They can now be updated remotely via the group host.
Printer identification. Find your printer in a crowd by triggering an identification sequence from the Cura Connect interface, making the selected printers frame lights flash.
Filter printers by type. If using Ultimaker 3 and Ultimaker S5 printers together in a group, they can be filtered by printer type.
Better queue management. Managing the queue is a lot more user-friendly due to the following features:
Duplicate job. After a job is added to the print queue, it can be duplicated up to 9 times at once.
Select/deselect multiple items. Multiple items can now be selected in the queue. Items can also be deleted in bulk, previously this had to be performed individually per item.
Reprint from recent history. Recently completed jobs are stored in the Cura Connect interface in chronological order. This includes an option to ‘reprint’ completed items, which places a job back in the queue to be printed again. Doing this side-steps having to send a job from Ultimaker Cura more than once.
New analytics page. The interface includes a new analytics tab that shows group performance, with dynamic charts that visually represent the data. Depending on the amount of data available, users can select the time period that all charts represent: ‘24 hours’, ‘1 week’, ‘1 month’, ‘3 months’, ‘6 months’, ‘1 year’, or ‘all time’. There are 4 charts in total:
Print job completion rate. This shows the all-time average and running average of finished vs. aborted print jobs within the chosen time period.
Print job configuration. Shows different print job configurations (materials, print cores, build plates) that have been started by the group within the chosen time period.
Material usage. Materials used for all print jobs, including jobs that have been aborted within the chosen time period.
Time in queue. Represents the average time that print jobs have spend in the queue before starting.
Print job history. Shows last 10 jobs added to the queue, including jobs that have finished printing, been aborted, or been deleted.
Data set export. A complete data set can be exported in CSV format for reporting, material stock forecasting, customer billing, etc.
Fixed crash when initiating the firmware update from the notification popup
Added homing switch diagnostic test
Print head is now centered when changing print cores or material
Fixed build plate being too hot when printer gives "confirm removal" prompt
Fixed material not moving when changing print core with PLA loaded in BB core or 0.25 AA core