Ultimaker TPU 95A (thermoplastic polyurethane) is a semi-flexible material that can be used in a wide variety of engineering applications where performance is more important than aesthetic qualities. Although most flexible filaments are usually difficult to print, Ultimaker TPU 95A is optimised for easier and faster printing without negatively affecting layer bonding.
Note: The information provided here applies to Ultimaker TPU 95A, similar quality cannot be guaranteed with third-party filaments.
In this article:
- Recommended settings and configurations
- Health and Safety
Ultimaker TPU 95A is supported on the Ultimaker S5, Ultimaker S3, Ultimaker 3, and Ultimaker 2+ (Connect). On these printers, it is compatible with the print core / nozzle sizes as shown in the below overview. You will need an AA print core to print TPU 95A on the Ultimaker S5, Ultimaker S3 and Ultimaker 3.
|Printer||Compatible print cores / nozzles|
|Ultimaker S5 (Pro Bundle)||AA 0.4, AA 0.8|
|Ultimaker S3||AA 0.4, AA 0.8|
|Ultimaker 3 (Extended)||AA 0.4, AA 0.8|
|Ultimaker 2+ Connect||0.25, 0.4, 0.6|
|Ultimaker 2+ (Extended)||0.25, 0.4, 0.6|
Note: Ultimaker TPU 95A is not supported on the Ultimaker 2 Go, Ultimaker 2 (Extended), Ultimaker Original+, and Ultimaker Original
Ultimaker TPU 95A has optimised settings for the Ultimaker Pro Bundle, Air Manager and Material Station. This ensures a good end of filament and end of print experience in the Material Station and an optimal build environment with the Air Manager. Please make sure to use the latest version of Ultimaker Cura and ensure the firmware has the latest update.
Because TPU 95A is prone to oozing, we don’t officially support printing TPU 95A in combination with other materials. However, on the Ultimaker S5, Ultimaker S3 and Ultimaker 3, TPU 95A can be printed experimentally in combination with PVA, Breakaway, ABS, Nylon, PC, or another color of TPU 95A. Be aware that dual-extrusion combinations with TPU 95A may result and stringing and blobs on the surface of the print. Results are dependent on the model type that is used.
Recommended settings and configuration
Note: Always use the latest version of Ultimaker Cura and make sure that your 3D printer is updated with the latest firmware version to include the correct material profile for Ultimaker TPU 95A.
TPU95A is prone to oozing. Therefore it is recommended to design and position your parts such that limited travels are needed. For printing multiple objects, the "one at a time" mode is recommended.
For printing TPU 95A a nozzle temperature of 220 - 235 °C is recommended. Furthermore, the TPU 95A profiles are optimised to print on a cold build plate on the Ultimaker S5 and Ultimaker 3, and on a build plate of 70 °C on the Ultimaker 2+.
Note: The correct temperatures are automatically used based on the printer, nozzle size, and profile you select in Ultimaker Cura.
Tip: Objects with a high amount of retractions print more reliably when the print temperature is raised with 2°C.
Tip: To make use of a cold build plate on a dual extrusion printer, it is important to disable the extruder that is not loaded with TPU, otherwise the highest build plate temperature will be chosen. This can be done in Ultimaker Cura using the "Enabled" checkbox.
In most instances, extra adhesion is not necessary for a successful print, but we always advise applying a thin layer of glue (included in the accessory box of your Ultimaker) to the glass plate for the best adhesion.
To improve adhesion when printing more complex prints with Ultimaker TPU95A, it is recommended to apply a thin layer of Magigoo Flex to the glass plate.
Caution: The addition of glue is recommended to improve adhesion and thereby prevent the chance of print failure and printer damage. Additionally, the use of glue can prevent overadhesion that can lead to damage to the build plate. Prints using Magigoo Flex as the adhesive may be difficult to remove. It is then recommended to place the buildplate in water and thereby dissolve the adhesive. More information can be found here.
Note: Do not use the adhesion sheets for Ultimaker TPU 95A. The adhesion is so strong that the sheet will tear after the removal of the first 3D print.
A brim is the default build plate adhesion type in the Ultimaker TPU 95A print profiles in Ultimaker Cura. A brim consists of extra lines printed around the perimeter of the initial layers of your model. This ensures reliable adhesion to the build plate.
After printing, it’s very easy to remove the print from the build plate after cooldown.
Ultimaker TPU 95A is not prone to warping or delamination, and prints reliably without additional accessories. However, you can try the front enclosure included in the Advanced 3D Printing Kit (for the Ultimaker 2+ or Ultimaker 3) to obtain more consistent and reliable results.
Furthermore, a relative humidity of below 50% is recommended when printed TPU 95A to prevent moisture uptake and limit oozing during printing.
Tip: It is recommended to dry Ultimaker TPU 95A before printing. The filament can be dried following the recommendations described in this article.
Health and safety
Ultimaker TPU 95A is safe to print when using the recommended temperature settings listed above. To ensure a comfortable and healthy working environment, we recommend 3D printing in a well-ventilated area.
For more information, download the safety data sheet for Ultimaker TPU 95A here.